Jingxin introduces the use and maintenance of electric forklift batteries
by:Jxforklift
2022-01-30
Jingxin carries the mission of providing high-quality forklift products and intelligent logistics equipment to users all over the world, and leading the development of China's forklift industry/electric forklifts and intelligent logistics equipment. We hope to get your continued care and support, and we will definitely gain more Successful experience has made greater achievements in the new round of development. So this time we will introduce the use and maintenance of electric forklift batteries! 1. The connection sequence when charging the electric forklift batteries is: first unplug the forklift battery socket, and connect the battery port (the socket on the movable end of the car) to the charger, Finally, connect the AC power supply of the charger to the mains AC380V or mains AC220V power supply. Turn on the charging switch, the working light will light up to start charging, and when the battery is full, the 'full indicator light' will light up to indicate full capacity. Note: Unplugging the charging plug during charging will cause an arc. Turn off the charger before unplugging the plug. After charging, there is a lot of hydrogen staying around the battery. No open flame is allowed. The cover on the battery should be opened for charging. 2. The battery should try to avoid overcharging and overdischarging. The single battery voltage should be recharged in time when the voltage drops to 1.70V. When the electricity meter shows 70% or less, it is overdischarged. Frequent overdischarge will affect the capacity of the battery. When the battery over-discharge is close to the limit value, the forklift control system will automatically start the protection function. First, the forklift lifting motor is restricted from working, and the walking motor can continue to work. At this time, the forklift should travel to the charging area to replenish the power. 3. The battery should be charged in time after each use, and the maximum time interval shall not exceed 24 hours. 4. The battery should be charged in a cool, ventilated, and away from open flame environment to avoid hydrogen explosion. 5. Prevent storage under power loss. Storage under power loss is the most harmful to the battery. Batteries that have not been used for a long time must be recharged once a month (normal charging method). 6. u200bu200bThe battery surface, connecting wires and bolts should always be kept clean and dry. 7. The battery connection must be kept in good contact, so as not to cause sparks to burn the pole or cause the battery to explode. 8. No harmful impurities should fall into the battery, and the instruments and utensils for measuring the density, temperature and liquid level of the electrolyte should be kept clean. 9. Do not place any conductive objects on the battery cover to avoid short-circuiting the battery. 1. Daily inspection 1. Liquid level: Lower than the rated liquid level will shorten the service life of the battery, and too little electrolyte will cause the battery to heat and damage. Therefore, you must always pay attention to whether the electrolyte is sufficient. 2. Terminals, wires, and covers: Always check the junctions of the battery terminals and the junctions with the wires for corrosion caused by oxidation, and check whether the cover is deformed and whether there is heat. 3. Appearance: Dirty battery surface will cause leakage. Keep the battery surface clean and dry at all times. 2. Regular maintenance. Check the battery electrolyte level (open the battery cover to check) and specific gravity every half month or whole month. Mineral water or electrolyte), the specific gravity should be adjusted when it deviates from the specified value.
To be the best worldwide provider of higher-value ABOUT US and the center for quality employment opportunities.
Helping our customers manage document workflow and increase efficiency through best-in-class ABOUT US and services. Fostering the growth and development of our employees.
First, in sparking the initial idea for a company based on manufacturing technology; and second, in designing a solution that could meet a clear market need for solving issues related to ABOUT US material handling racks.
To be the best worldwide provider of higher-value ABOUT US and the center for quality employment opportunities.
Helping our customers manage document workflow and increase efficiency through best-in-class ABOUT US and services. Fostering the growth and development of our employees.
First, in sparking the initial idea for a company based on manufacturing technology; and second, in designing a solution that could meet a clear market need for solving issues related to ABOUT US material handling racks.
Custom message