Jiangsu electric forklift manufacturers share that the water level of the battery needs to exceed the built-in plate when replenishing water, but not too much

by:Jxforklift     2021-12-18
Since mechanization began to develop vigorously, labor has gradually withdrawn from the 'stage'. Generally speaking, the loading and unloading of large objects all rely on machinery and equipment. For the loading and unloading of these large objects, electric forklifts are inevitably needed. Electric forklifts make good use of electricity for loading and transportation operations, which also means that their batteries will always be in a state of charging and discharging. In addition, the operating frequency of electric forklifts is more, which will easily affect the life of the battery. Impact. How to extend the service life of the battery has become a problem. Let's talk about it from the Jiangsu electric forklift manufacturer. 1. When the battery is charged and discharged, the battery liquid level changes: 1. When the battery is discharged: the battery liquid seeps into the pores of the battery plate, so the battery liquid level will drop. 2. When the battery is charging: the battery fluid is discharged from the pores of the battery plate, so the battery fluid level will rise. 2. About the loss of battery liquid: 1. When the battery is being charged, especially near the Cassing Condition, the electrical reaction is that the water in the battery liquid is electrolyzed. The overflow of hydrogen (H) and oxygen (O) gases reduces the battery liquid capacity and increases the concentration. 2. The above reaction will also occur when the battery is discharged, but it is not strong when it is charged, but when the battery is continuously discharged with a large current, the above reaction will lose water quite strongly. 3. In the fierce electrochemical reaction, if the battery liquid level is too high, the discharged gas will splash and overflow with the battery liquid, and the battery liquid level will drop (the sulfuric acid H2SO4 in the battery liquid will follow the battery liquid Overflow and loss). If supplementary pure water is used to maintain the liquid level, the liquid level of the battery liquid will change (that is, the specific gravity of the battery liquid is insufficient). Since the splash and overflow of the battery fluid of each unit are different, the specific gravity of each unit cell is inconsistent after such water replenishment, forming a potential difference between the unit cells, which affects the efficiency of the battery. Therefore, try to avoid this situation in battery use. 3. Why do we need to add pure water: 1. It is required that the electrode plate must be immersed in the battery liquid at any time regardless of the change of the battery liquid level (the electrode plate should not be exposed to the battery liquid), so that it can give full play to its design requirements (capacity) ). The battery capacity is related to the area of u200bu200bthe battery liquid that the battery plate contacts. 2. During the operation of the battery, the concentration of the battery liquid should be maintained and the consistency of the concentration between the individual cells should be maintained. Otherwise, there will be a potential difference between each unit cell, generating a circulating current and affecting the efficiency of the battery pack. The battery voltage is related to the concentration of the battery fluid. 3. The correct supplement of water has an important impact on the performance and service life of the battery and can reduce and reduce sulfation. 4. How to replenish water: 1. It must be done within 1-2 hours after the battery is fully charged. 2. After the battery is used, measure the liquid level (based on the splash plate), and it should still be possible (confirm in the last charge and discharge cycle) The inner battery plate is not exposed) detected. 3. After refilling, the liquid level should be 5-10 mm higher than the splash plate, but not too high (take the splash plate as the reference). 4. After several charge and discharge cycles, when the battery liquid is charged to the point where it can no longer be recharged, measure the specific gravity of the battery liquid. If the specific gravity is too low or the specific gravity of each unit cell is inconsistent, sulfuric acid should be added. Re-adjust the specific gravity to (1.27-1.29) G/CM3 (make the specific gravity of each unit cell close to the same). Charge it after adjustment to make the battery liquid even, this item should be carried out by professionals. V. Precautions: 1. In normal use, within a charge and discharge cycle, the water loss of a unit battery is about 4ml/100Ah of water. Example: A 500Ah unit battery should be supplemented with approximately 20ml of pure water. 2. After refilling, the liquid level of the battery liquid must not exceed the splash plate by 10mm. The reasons are: A. The liquid level is too high, and the battery liquid capacity contacts the aluminum row welded between the battery plates, which will form ion pollution of the battery liquid , So as to strengthen the discharge of the battery pack and damage the battery capacity and life. B. Excessive liquid level will cause the battery liquid to splash and overflow during the electrochemical reaction, resulting in a decrease in the concentration of the battery liquid, thereby reducing the battery capacity and battery voltage. In addition, the splashed battery fluid will corrode the car body and the battery. 3. If the battery liquid level is insufficient, when the battery is in use, the upper part of the battery plate will be exposed to the battery liquid, which reduces the area of u200bu200bthe battery plate that participates in the electrochemical reaction and reduces the battery capacity. The above is the tips for extending the life of electric forklift batteries introduced by the editor. I believe you will be able to gain something after reading it. The company has always adhered to the corporate culture of 'quality casts the future of the enterpriseWe sincerely welcome new and old customers at home and abroad to visit us.
Jiangsu Jingxin Lifting Equipment Co., Ltd. is trying to institute social good changes this relationship because it averts a firm's resources from its core task of increasing profits.
You can always ask the experts for the most appropriate industrial lifting devices ABOUT US for your specific needs. Find the best support, prices and other to ABOUT US solutions at Jingxin forklift.
In conjunction with retraining and upskilling efforts, Jiangsu Jingxin Lifting Equipment Co., Ltd.’s workers should focus on growing unique human skills that high-tech machines are unable to replicate, such as strategic and abstract thinking, complex communications, creativity and leadership competencies.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...
Dear friends, It may be due to time difference, so we cannot reply in time. We will contact you as soon as possible. My whatspp and wechat number is :+86 18136936691.